Cisco ME 1200 Series Carrier Ethernet Access Devices Controller Configuration Guide, Cisco IOS 15.6(1)SN and Later Releases - Configuring Y.1564 [Cisco ME 1200 Series Carrier Ethernet Access Devices] (2024)

This document describes the Y.1564 test feature and configuration stepsto execute Y.1564 feature.

Prerequisites for Configuring Y.1564
Information About Y.1564

Prerequisites for Configuring Y.1564

You must disable:
- Link Layer Discovery Protocol (LLDP) transmit and receive on source port.
  See Also
  Configuration Guide for Cisco NCS 4000 Series - Configure Ethernet Service Activation Test [Cisco NCS 4016]Y.1564 Service Activation Testing on NCS : Part1
- Loop protection on destination port or Spanning Tree Protocol (STP) on destination and source port.
- Spanning Tree Protocol (STP).
NID must have an IP address.
Loop should not be configured.

Information About Y.1564

ITU-T Y.1564 (Or sometimes calledY.156sam or EtherSAM - Ethernet Service Activation Methodology) is a QoS andnetwork performance ITU-T Ethernet-based service test methodology. This testingprocedure tests service turn-up, installation and troubleshooting ofEthernet-based services.

Y.1564 allows simultaneous testing of multiple Ethernet services andmeasures. It also validates the different QoS mechanisms provisioned in thenetwork to prioritize different service types - allowing faster deployment,easier service and network troubleshooting.

Configuring New Y.1564 Profile
Getting the Profile Configuration using Profile Name
Viewing Profile Names
Configuring Y.1564 Test Parameters

Configuring New Y.1564 Profile

	Command or Action	Purpose
Step1	configure terminal Example: Switch# configure terminal	Enters globalconfiguration mode.
Step2	controller nid1/NID_ID Example: Switch(config)# controller nid 1/1	Enters thecontroller configuration mode.
Step3	ciscoY1564 Example: Switch(config-controller)# ciscoY1564	Enters ciscoY1564 configuration mode.
Step4	setY1564Profile y1564ProfileProfile name\|description\|acceptable-fdv acceptable-gdv\|acceptable-flr acceptable-flr\|acceptable-ftd acceptable-ftd \| cir-test {dm-interval dm-interval \|duration duration \| step-count step-count \| start { enable \| disable } } \| dst-oam- aware { enable \| disable } \| dwell-time dwell-time \| eir-test { enable \| disable } \| meg-level meg-level duration \| performance-test { enable \| disable } \| traffic-policing-test { dm-interval \| duration } \| } traffic-type { customer-simulated \| oam} \| emix\| user-defined-frame-size } Example: Switch(config-controller-ciscoY1564)# setY1564Profile y1564Profile profileNameSwitch(config-controller-ciscoY1564)# setY1564Profile y1564Profile descriptionSwitch(config-controller-ciscoY1564)# setY1564Profile y1564Profile acceptable-fdv 0-10000Switch(config-controller-ciscoY1564)# setY1564Profile y1564Profile acceptable-flr 0-1000Switch(config-controller-ciscoY1564)# setY1564Profile y1564Profile acceptable-ftd 0-10000Switch(config-controller-ciscoY1564)# setY1564Profile y1564Profile cir-test start enableSwitch(config-controller-ciscoY1564)# setY1564Profile y1564Profile cir-test dm-interval 100-10000Switch(config-controller-ciscoY1564)# setY1564Profile y1564Profile cir-test duration <cr>Switch(config-controller-ciscoY1564)# setY1564Profile y1564Profile cir-test step-count 1-1000Switch(config-controller-ciscoY1564)# setY1564Profile y1564Profile dst-oam-aware enableSwitch(config-controller-ciscoY1564)# setY1564Profile y1564Profile dwell-time 100-10000Switch(config-controller-ciscoY1564)# setY1564Profile y1564Profile eir-test enableSwitch(config-controller-ciscoY1564)# setY1564Profile y1564Profile meg-level 0-7Switch(config-controller-ciscoY1564)# setY1564Profile y1564Profile performance-test enableSwitch(config-controller-ciscoY1564)# setY1564Profile y1564Profile traffic-policing-test dm-interval 100-10000Switch(config-controller-ciscoY1564)# setY1564Profile y1564Profile traffic-policing-test duration <cr>Switch(config-controller-ciscoY1564)# setY1564Profile y1564Profile traffic-policing-test duration start enableSwitch(config-controller-ciscoY1564)# setY1564Profile y1564Profile traffic-typeSwitch(config-controller-ciscoY1564)# setY1564Profile y1564Profile traffic-type customer-simulated <cr>Switch(config-controller-ciscoY1564)# setY1564Profile y1564Profile traffic-type oam <cr>Switch(config-controller-ciscoY1564)# setY1564Profile y1564Profile emixSwitch(config-controller-ciscoY1564)# setY1564Profile y1564Profile e emix USwitch(config-controller-ciscoY1564)# setY1564Profile y1564Profile user-defined-frame-size 10000	profileName— Enter the name of the profile for Y1564 . description— Enter a brief description about the profile . acceptable-fdv— Enter frame delay variation in milliseconds to configure Y1564. Acceptable limit is 0-10000. The default value is 0, which disables the test. acceptable-flr— Enter frame loss ratio per mile to configure Y1564. Acceptable limit is 0-1000. The default value is 0 and 1000 disables the test. acceptable-ftd— Enter frame transfer delay in milliseconds to configure Y1564. Acceptable limit is 0-10000.Acceptable limit is 0-10000. The default value is 0, which disables the test. cir-test— Enter frame delay variation in milliseconds to configure Y1564. Acceptable limit is 0-10000. dm-interval—Enter the interval of between sending delay measurement frame. Acceptable limitis 100-10000. duration—Enter the duration of one step. step-count—Enter the number of steps to configure CIR. Acceptable limit is 1-1000 start—Enterenable or disable to configure CIR test. dst-oam-aware— Enter enable or disable to configure remote end Y.1731 OAM aware. dwell-time— Enter the time frame of execution, pauses in milliseconds after each trial before reading counters, and status from hardware. Acceptable limit is 100-10000. Default value is 500. eir-test— Enter EIR configuration test and optionally set its parameters to configure Y1564. Parameters are dm-interval, duration and start. meg-level— Enter the profile MEG level to configure Y1564 . Acceptable limit is 0-7. performance-test— Enter the performance test parameters. dm-interval—Enter the time interval in milliseconds between sending delay measurementframe. Acceptable limit is 100-10000. duration—Enter the duration of performance test. start—Enterenable or disable to start the performance test. traffic-policing-test— Enter the traffic policing test parameters.. dm-interval—Enter the time interval in milliseconds between sending delay measurementframe. Acceptable limit is 100-10000. duration—Enter the duration of traffic policing test. start—Enterenable or disable to start the traffic policing test. traffic-type— Enter the type of traffic generated at the near end. customer-simulated— Enter the frames that simulatereal customer traffic as background traffic. oam— Enterthe duration of traffic policing test. emix— select the frame size(EMIX letter-encoded) that the enabled tests will use. Encoding is as follows: a: 64, b: 128, c: 256, d: 512, e: 1024,f: 1280, g: 1518, h: MTU, u: user-defined. user-defined-frame-size— Enter the frame size if emix is set to 'U'. Acceptable limit is 64-10236
Step5	review Example: Switch(config-controller-ciscoY1564)# setY1564Profile review	Reviews the ciscoY1564 profile configuration parameters.
Step6	commit Example: Switch(config-controller-ciscoY1564)# setY1564Profile commit	Sends the ciscoY1564 profile parameters to the NID.
Step7	exit Example: Switch(config-controller-ciscoY1564)# exit	Exits the config controllermode.

Getting the Profile Configuration using Profile Name

	Command or Action	Purpose
Step1	configure terminal Example: Switch# configure terminal	Enters global configuration mode.
Step2	controller nid1/NID_ID Example: Switch(config)# controller nid 1/1	Enters the controller configuration mode.
Step3	ciscoY1564 Example: Switch(config-controller)# ciscoY1564	Enters ciscoY1564 configuration mode.
Step4	getY1564ProfilegetY1564ProfileReq Example: Switch(config-controller-ciscoY1564)# getY1564Profile getY1564ProfileReq	Retrieves the Profile configuration.
Step5	getY1564Profilereview Example: Switch(config-controller-ciscoY1564)# getY1564Profile review	Displays the Y.1564 profile configuration.
Step6	getY1564Profilecommit Example: Switch(config-controller-ciscoY1564)# getY1564Profile commit	Sends the Y.1564 profile configuration information to the NID.
Step7	exit Example: Switch(config-controller-ciscoY1564)# exit	Exiits the config controller mode.

The following example shows the Profile Configuration using the Profile Name:

Switch(config-controller)# getY1564Profile commit GetY1564Profile_Output.y1564Profile.y1564Profile_ELEM_0.profileName = 'cisco123456'GetY1564Profile_Output.y1564Profile.y1564Profile_ELEM_0.description = 'oamunaware'GetY1564Profile_Output.y1564Profile.y1564Profile_ELEM_0.acceptable_fdv = 0GetY1564Profile_Output.y1564Profile.y1564Profile_ELEM_0.acceptable_ftd = 0GetY1564Profile_Output.y1564Profile.y1564Profile_ELEM_0.acceptable_flr = 0GetY1564Profile_Output.y1564Profile.y1564Profile_ELEM_0.dst_oam_aware = falseGetY1564Profile_Output.y1564Profile.y1564Profile_ELEM_0.dwell_time = 500GetY1564Profile_Output.y1564Profile.y1564Profile_ELEM_0.emix = '1024'GetY1564Profile_Output.y1564Profile.y1564Profile_ELEM_0.meg_level = 7GetY1564Profile_Output.y1564Profile.y1564Profile_ELEM_0.traffic_type.t = 1GetY1564Profile_Output.y1564Profile.y1564Profile_ELEM_0.traffic_type.u.oam = '0'GetY1564Profile_Output.y1564Profile.y1564Profile_ELEM_0.user_defined_frame_size = 2000GetY1564Profile_Output.y1564Profile.y1564Profile_ELEM_0.cir_test.start = trueGetY1564Profile_Output.y1564Profile.y1564Profile_ELEM_0.cir_test.duration = 60GetY1564Profile_Output.y1564Profile.y1564Profile_ELEM_0.cir_test.dm_interval = 500GetY1564Profile_Output.y1564Profile.y1564Profile_ELEM_0.cir_test.step_count = 4GetY1564Profile_Output.y1564Profile.y1564Profile_ELEM_0.eir_test.start = trueGetY1564Profile_Output.y1564Profile.y1564Profile_ELEM_0.eir_test.duration = 60GetY1564Profile_Output.y1564Profile.y1564Profile_ELEM_0.eir_test.dm_interval = 500GetY1564Profile_Output.y1564Profile.y1564Profile_ELEM_0.performance_test.start = trueGetY1564Profile_Output.y1564Profile.y1564Profile_ELEM_0.performance_test.duration = 10GetY1564Profile_Output.y1564Profile.y1564Profile_ELEM_0.performance_test.dm_interval = 100GetY1564Profile_Output.y1564Profile.y1564Profile_ELEM_0.traffic_policing_test.start = trueGetY1564Profile_Output.y1564Profile.y1564Profile_ELEM_0.traffic_policing_test.duration = 10GetY1564Profile_Output.y1564Profile.y1564Profile_ELEM_0.traffic_policing_test.dm_interval = 100 GetY1564Profile Commit Success

Viewing Profile Names

	Command or Action	Purpose
Step1	configure terminal Example: Switch# configure terminal	Enters global configuration mode.
Step2	controller nid1/NID_ID Example: Switch(config)# controller nid 1/1	Enters the controller configuration mode.
Step3	ciscoY1564 Example: Switch(config-controller)# ciscoY1564	Enters ciscoY1564 configuration mode.
Step4	showY1564showY1564Req{profiles\|reports} Example: Switch(config-controller-ciscoY1564)# showY1564 showY1564Req	Displays existing profiles or report information.
Step5	showY1564review Example: Switch(config-controller-ciscoY1564)# showY1564 review	Displays the profile configurations.
Step6	exit Example: Switch(config-controller-ciscoY1564)# exit	Exits the config controller mode.

The following example shows the configurations to display a particular Profiles using the profile name or description:

Switch(config-controller-ciscoy1564)#showY1564 commit ShowY1564_Output.showY1564Resp.t = 1ShowY1564_Output.showY1564Resp.u.profile[0].profileName = 'NewProfile1'ShowY1564_Output.showY1564Resp.u.profile[0].description = ''ShowY1564_Output.showY1564Resp.u.profile[1].profileName = 'cisco123456'ShowY1564_Output.showY1564Resp.u.profile[1].description = 'oamunaware'ShowY1564 Commit Success

Managing Y.1564 Profile Names

	Command or Action	Purpose
Step1	configure terminal Example: Switch# configure terminal	Enters globalconfiguration mode.
Step2	controller nid1/NID_ID Example: Switch(config)# controller nid 1/1	Enters thecontroller configuration mode.
Step3	ciscoY1564 Example: Switch(config-controller)# ciscoY1564	Enters ciscoY1564 configuration mode.
Step4	y1564ProfileManagement\|old-y1564ProfileManagmentReq{delete\|rename{new-name\|old-name}} Example: Switch(config-controller-ciscoY1564)# y1564ProfileManagement y1564ProfileManagmentReq rename old-name cisco123456Switch(config-controller-ciscoY1564)# y1564ProfileManagement y1564ProfileManagmentReq rename new-name ciscoSwitch(config-controller-ciscoY1564)# y1564ProfileManagement y1564ProfileManagmentReq delete cisco	rename—Set rename to rename a old profile name. delete—Set delete to delete an existing profile.
Step5	review Example: Switch(config-controller-ciscoY1564)# y1564ProfileManagement review	Reviews the ciscoY1564 profile names.
Step6	commit Example: Switch(config-controller-ciscoY1564)# y1564ProfileManagement commit	Sends the changed or deleted ciscoY1564 profile names to the NID .
Step7	exit Example: Switch(config-controller-ciscoY1564)# exit	Exits the config controllermode.

Configuring Y.1564 Test Parameters

	Command or Action	Purpose
Step1	configure terminal Example: Switch# configure terminal	Enters globalconfiguration mode.
Step2	controller nid1/NID_ID Example: Switch(config)# controller nid 1/1	Enters thecontroller configuration mode.
Step3	ciscoY1564 Example: Switch(config-controller)# ciscoY1564	Enters ciscoY1564 configuration mode.
Step4	setY1564TestParamsy1564TestsReq { dei\|description \|dscp\|ece \| evc \| interface \| pcp \| peer-mac \| profile-name \| report-name \| vlan vlan-id } Example: Switch(config-controller-ciscoY1564)# setY1564TestParams y1564TestsReq profile-name cisco123456 Switch(config-controller-ciscoY1564)# setY1564TestParams y1564TestsReq report-name controllerreport123456 Switch(config-controller-ciscoY1564)# setY1564TestParams y1564TestsReq description dstmodeno Switch(config-controller-ciscoY1564)# setY1564TestParams y1564TestsReq evc 1 Switch(config-controller-ciscoY1564)# setY1564TestParams y1564TestsReq ece 1 Switch(config-controller-ciscoY1564)# setY1564TestParams y1564TestsReq interface 3 Switch(config-controller-ciscoY1564)# setY1564TestParams y1564TestsReq peer-mac 00-00-00-00-00-01 Switch(config-controller-ciscoY1564)# setY1564TestParams y1564TestsReq pcp 2 Switch(config-controller-ciscoY1564)# setY1564TestParams y1564TestsReq vlan untagged Switch(config-controller-ciscoY1564)# setY1564TestParams y1564TestsReq dei 0 Switch(config-controller-ciscoY1564)# setY1564TestParams reviewSwitch(config-controller-ciscoY1564)# setY1564TestParams commit	dei— Enter the DEI number of the profile. The valid range is 0-1. description— Enter the description about the test. dscp— Enter the DSCP number of the profile. The valid range is 0-63. ece— Enter the ECE ID number of the profile, on which the test needs to be executed. The valid range is 1-1024. evc— Enter the EVC ID number of the profile. The valid range is 1-1024. interface— Enter the UNI port. The valid range is 1-125. pcp— Enter the PCP number of the profile. The valid range is 0-7. peer-mac— Enter peer MAC address. profile-name— Enter the name of the existing profile, that needs to be tested. report-name— Enter a unique name for the test report. vlan— Enter the Vlan ID.
Step5	review Example: Switch(config-controller-ciscoY1564)# setY1564TestParams review	Reviews the ciscoY1564 profile test parameters.
Step6	commit Example: Switch(config-controller-ciscoY1564)# setY1564TestParams commit	Sends the test parameter reports to the NID.
Step7	exit Example: Switch(config-controller-ciscoY1564)# exit	Exits the config controller mode.

Configuration Example

when profile is configured as DST, then OAM-aware port and peer-mac address need to be specified in setY1564TestParams.

Switch(config-controller)# ciscoY1564Switch(config-controller-ciscoY1564)# setY1564TestParams y1564TestsReqSwitch(config-controller-ciscoY1564)# setY1564TestParams y1564TestsReq profile-name cisco123456 Switch(config-controller-ciscoY1564)# setY1564TestParams y1564TestsReq report-name controllerreport123456 Switch(config-controller-ciscoY1564)# setY1564TestParams y1564TestsReq description dstmodenoSwitch(config-controller-ciscoY1564)# setY1564TestParams y1564TestsReq peer-mac 00-02:01:00:01:03 Switch(config-controller-ciscoY1564)# setY1564TestParams y1564TestsReq evc 1 Switch(config-controller-ciscoY1564)# setY1564TestParams y1564TestsReq ece 1 Switch(config-controller-ciscoY1564)# setY1564TestParams y1564TestsReq interface 3 Switch(config-controller-ciscoY1564)# setY1564TestParams reviewSwitch(config-controller-ciscoY1564)# setY1564TestParams commit

Viewing Y.1564 Test Parameters

	Command or Action	Purpose
Step1	configure terminal Example: Switch# configure terminal	Enters globalconfiguration mode.
Step2	controller nid1/NID_ID Example: Switch(config)# controller nid 1/1	Enters thecontroller configuration mode.
Step3	ciscoY1564 Example: Switch(config-controller)# ciscoY1564	Enters ciscoY1564 configuration mode.
Step4	getY1564TestParamsgetY1564TestsReq Example: Switch(config-controller-ciscoY1564)# getY1564TestParams getY1564TestsReq	Retrieves the parameters set for latest tet.
Step5	review Example: Switch(config-controller-ciscoY1564)# getY1564TestParams review	Reviews the ciscoY1564 profile configuration parameters.
Step6	commit Example: Switch(config-controller-ciscoY1564)# getY1564TestParams commit	Sends the test parameter reports to the NID.
Step7	exit Example: Switch(config-controller-ciscoY1564)# exit	Exits the config controllermode.

Saving Y.1564 Test Report

	Command or Action	Purpose
Step1	configure terminal Example: Switch# configure terminal	Enters global configuration mode.
Step2	controller nid1/NID_ID Example: Switch(config)# controller nid 1/1	Enters the controller configuration mode.
Step3	ciscoY1564 Example: Switch(config-controller)# ciscoY1564	Enters the ciscoY1564 configuration mode.
Step4	y1564ReportManagement y1564ReportManagementReqsave\|stop Example: Switch(config-controller-ciscoY1564)# y1564ReportManagemen y1564ReportManagementReq save reportName controllerreportSwitch(config-controller-ciscoY1564)# y1564ReportManagemen y1564ReportManagementReq save tftpPath tftp://202.153.144.25/auto/tftp-blr-users1/sharsh	Save—Set save to save a profile test report. Stop—Set stop to stop an ongoing profile test .
Step5	review Example: Switch(config-controller-ciscoY1564)#y1564ReportManagement review	Reviews the ciscoY1564 profile test report.
Step6	commit Example: Switch(config-controller-ciscoY1564)#y1564ReportManagement commit	Sends the ciscoY1564 profile test report to the NID.
Step7	exit Example: Switch(config-controller-ciscoY1564)# exit	Exits the config controller mode.

Deleting Y.1564 Test Report

	Command or Action	Purpose
Step1	configure terminal Example: Switch# configure terminal	Enters globalconfiguration mode.
Step2	controller nid1/NID_ID Example: Switch(config)# controller nid 1/1	Enters thecontroller configuration mode.
Step3	ciscoY1564 Example: Switch(config-controller)# ciscoY1564	Enters the ciscoY1564 configuration mode.
Step4	y1564ReportManagement y1564ReportManagementReq{delete\|stop} Example: Switch(config-controller-ciscoY1564)# y1564ReportManagemen y1564ReportManagementReq delete controlerreport	delete—Set delete to delete an existing profile test report. Stop—Set stop to stop an ongoing profile test .
Step5	review Example: Switch(config-controller-ciscoY1564)# y1564ReportManagement review	Reviews the ciscoY1564 profile test report.
Step6	commit Example: Switch(config-controller-ciscoY1564)# y1564ReportManagement commit	Sends the ciscoY1564 profile test report to the NID.
Step7	exit Example: Switch(config-controller-ciscoY1564)# exit	Exits the configcontroller mode.